www.86garage.com

All prices are O.B.O. For those not listed, make me an offer. Just get in touch with me.




AE92 Throttle Body $15
It doesn't have the same idle bypass as the AE86, but that can be fixed by drilling a hole I think. In the second picture you can see the bypass hole in the same place as the AE86 RWD throttle body. In the third picture you can see the hole on the right is closed off. This was the 92 bypass hole. The hole on the left is for the 86. Only problem is that the hole is not physically connected to the hole before the butterfly. A small drill bit could probably open in up though. I'll take a look at it and drill the hole if someone is interested.




AE101 GZE Flywheel $30



Stock Cams Sets: $20/ea set
Bigport MR2 Set
Bigport AE86Set
AE101 GZE (wrapped in newspaper).
The set on the lower left is either a smallport set of cams or another bigport 86 set.


Want it? You can have it.


TPS: $15/ea (Check the part numbers in the pick if your interested, just to ensure you can use them...I pulled them from MR2's)




Flywheels (one is definitely a 16v bigport flywheel. the other is either a hi-comp flywheel or a bigport 16v flywheel.) $30 each


Heater Core: $15 Not sure if it can be fixed. It doesn't leak though.


EGR Equipment: $30 for all. I have two charcoal canisters. One has a torn lower vent tube...can be replaced I'm sure.


Bai-ding Plug wires: $25 They were meant for a Camry, but worked find on my 16V. The bulge is supposed to be a capacitor.



FWD Starter Plate: $15
RWD Power steering knuckles: $20


Engine Mount Covers: $10
Pwr Rack Brackets: $10


Water Pump Pullies: $10/ea
Crank Pullies: $15 (only have the AE92 Hi-comp pulley left)
Crank timing Sprocket: $20
Tensioner Pulley: $15
Spark Plug Valley Cover: $15



Oil Pressure Sender: $15


RWD Intake Manifold: $30
FWD/Mid Engine Intake Manifold: $25
GTS Brake Booster: $50
Starter Heat Shield: $15
Passanger-side Engine Bracket: $15
GTS Clutch Master Cylinder: $25



The longer one lines up with my Smallport head, but I'll double check. The other is physically shorter and the ports are closer together. I don't have a bigport head so I can't verify that's what its for.
Smallport rail: Sold Blue-Top/Bigport Rail: $20





Ignitor: $10 (I'll get part number later)


Ueo Replica Fender Braces $100





Coils: $15/ea
Ignitors: All Sold








1-Kouki LSD Axle: $60
1-Kouki Oped Diff Axle: $40
1-Kouki Open Diff Pumpkin/Ring/Pinion: $50
1-Toyota Crush Sleeve: $10










TE manual rack and pinion gears: $40 This is the internals for the rack that contains my QSR. I'm assuming you could put this in any MR2 manual rack case. I don't know if there is a discernible difference between the two gear sets, other than the pinion length

This is the rack housing they came from:


Here are the internals that are for sale:



Kouki USDM Tail lights: $50

is that 40 for the power steering stuff all shipped? Do you have the lines that come from the pump as well? Also, do you have a cold start injector?

I can get you a shipping price. Just give me your zip. I don't have the lines that run from the pump to the rack or the return line. I'll double check just to make sure though. I'll get on that this weekend. I'll also look for a cold start injector. I thought I had one or two laying around somewhere.

Zip is 75021 and thanks. Just let me know

I'm at work right now, so I don't have access to the parts to get a definite weight or box size, but through UPS shipping looks to be roughly $18. I'm assuming that's mostly due to the weight though. The pump and the bracket aren't the lightest pieces. I'll get a more definite quote either tonight or tomorrow morning.

no rush, just let me know.

It looks like it would be $58 shipped. Just let me know.

I also put some more parts I have for sale in the first post.

pm sent

on that rack. Is it the everything I need to put the rack? I would rather have the rack if so. Let me know.

There is not housing for the rack. You would need a TE, AE, or MR housing to install these internals. These are just the gears I had left after I installed the QSR.

GTSRolla34 wrote:There is not housing for the rack. You would need a TE, AE, or MR housing to install these internals. These are just the gears I had left after I installed the QSR.

ah ok, well give me a paypal email to send the $58 too. Did you find a cold start injector by chance?

I have seen that engine bay before your over off HWY-90 right. I will take those inner tierods off of your hands if you still have them.

Thanks,
David

I still have the tie rods. Just let me know for sure.

New Parts For Sale: (I'll get pictures as soon as it's possible)

AE86 Front Lower Control Arms (cleaned rust removed and repainted) with Prothane Poly Bushings, Moog Ball Joints (with grease fittings), T3 Steering Knuckles: $150
(if you want the moog inner tie rods also, I'll take $180 for everything)

Again, I'll get pics as soon as I can.

AE86 Front Lower Control Arms (cleaned rust removed and repainted) with New Prothane Poly Bushings (Installed), New Moog Ball Joints (with grease fittings - Installed), T3 Power Steering Knuckles, and Stock Power Steering Knuckles (cleaned of rust and repainted): $150
(if you want the moog inner tie rods also, I'll take $180 for everything)