www.86garage.com

I am looking for a good Circuit open relay and the coolant outlet block from the back of the head. let me know what you got. post pics if you got any thanks

If you were in dallas me and mckenney would help ya out but we a couple hours north

bt20v wrote:If you were in dallas me and mckenney would help ya out but we a couple hours north

well if your in the houston area any time soon let me know and thanks

Sean, what's wrong with it?

Jump the COR

dr.occa wrote:Sean, what's wrong with it?

I dont know i still havent been able to get it running since the motor you sold me. I can get it to run but not rev. it doesnt even idle well when it does. it stumbles and dies. iv tried changing so many parts but in the end i have no clue what is wrong with it. my brother in law thinks there is no gas getting to the cylinders but it will start and idle some times if i hold the flap open on the afm but it dies if the throttle is pushed. there is also plenty of fuel pressure at the rail. Iv tried 2 other ecus 2 other afms and 2 other sets of injectors. i did new plugs wires cap rotor and coil. it gets spark now btw.i also changed the intake tube since my old one was cracked. it has none of the emision stuff but that was all gone when i got the car and it ran when i bought it.

also if some one has an injector resistor box and a gts distributor i will buy those too

JDM AE86 wrote:Jump the COR

what is the COR?

Circuit
Open
Relay

I have a few injector boxes here. Remeber where I live? Almost sounds like the fuel pump get the few seconds of prime then shuts off letting it idle for a few seconds then dying. I have a strong feeling if you jump the COR it will run.

JDM AE86 wrote:Circuit
Open
Relay

I have a few injector boxes here. Remeber where I live? Almost sounds like the fuel pump get the few seconds of prime then shuts off letting it idle for a few seconds then dying. I have a strong feeling if you jump the COR it will run.

I think i might have done that. is that in the diagnostic box, jump port +B and FP? i dont think it is anything to do with the fuel pump there is always pressure at the fuel rail and plenty of it. could it be the FPR? think it might be the distributor, maybe the injector box or something with the injector circuit. Iv even tested my efi relay and the main relay and they all test good. but like i said i dont know whats wrong or i would be driving it.

I dont know why the COR would have changed tho. i only changed the motor and didnt do anything to the wiring harness. ill try it again tho. i rebuilt my distributor with the kbox kit since it was leaking oil. oh yea when i was doing my fuel lines and starting the car to see if there was any fuel leaks it would prime on start up. my car also doesnt advance when i jump the terminals to set my base timing either. that is also an issue i want to tackle. for the time being iv been setting it to 16 deg

yea i remember where you live. I actually pass that area on my way home from work. what time are you available. also how much for the resistor box?

ok so as jdm ae86 said it was the cor. i jumped it in the diagnostic box. i did try it before but it didnt work the first time due to my tvis plate having a vacuum leak. it worked this time since i removed it. thanks jdm ae86 for the advise. If anyone has a circuit open relay ill buy it off of you. does any one have one from a parts car?

JDM AE86 wrote:

haha tell me about it. the tvis plate had a vac leak and that was my problem. do you have a circuit open relay hanging around your place?

ga_goosh wrote:

JDM AE86 wrote:

haha tell me about it. the tvis plate had a vac leak and that was my problem. do you have a circuit open relay hanging around your place?

yeeeeeep

JDM AE86 wrote:

ga_goosh wrote:

JDM AE86 wrote:

haha tell me about it. the tvis plate had a vac leak and that was my problem. do you have a circuit open relay hanging around your place?

yeeeeeep

awesome. thats great. can i get it today? around 4 to 430? i can wait till later if you need to

ok i now have a running ae86 yay. thanks Corey for the great deal on the parts. everything worked out great. lock thread Jonas

ga_goosh wrote:ok i now have a running ae86 yay. thanks Corey for the great deal on the parts. everything worked out great. lock thread Jonas

Cool beans dude let me know if I can help anymore.