www.86garage.com

ok so i finaly sat down and took the time to put up some pictures of my corolla and all its been thru. endjoy.

what it look like shortly after i got it.

after hitting a curb.

fixed that, dicided to go drifting.


broke the stock lat bar so got a new one.

couldn't stop there, so i added a header, 4 link and springs.



oh yeah and kyb agx's

headed for austin and some lady went off the road in front of me and hit a gaurdrail. the result


bother rims were lost.
what the rims looked like before

what it looked like before i f-bombed it up.


what i still have to put in.

they way it is now due to wet road, understear and crappy tires.


thats it for now. just looking for a lower control arm.

enjoy.

should've put this in the toyota section but nice coupe... most down here are hatch's.

when i got the car the stock springs had been cut by more then half so it was sow low and had no body roll at all. so easy to drift. lol.

thanks for sharing your 86 with us!

been there, done that, heated it up and bent it back in place.

works great, I reinforced all the shit that bent, so it will bend the frame if I hit it hard enough next time.

lol. thats the same thing that happend to my rear end. only on the passanger side. snapped clean off. had the e-brake up and was looking at it. i was like dude i can just bend it back and drive it home. my friend was like no you can't. he drops the e-brake and the wheel just dropped off. i was like oh, yeah your right. lol.

as far as the part i checked w/everyone i could and no one has it. only the dealer and they want $200+ or so. so i'm looking for the part. i don't have anything to heat it up with. or reinforce it.

nice coupe....not bad

ok i forgot to put the spec's of the car on here.

steel braided brake lines
4-2-1 header
ngk iridium spark plugs
8.5mm wires
t3 adj lat bar
tcsportline adj 4-link
electric fan
front upper strut bar
c-pilar bar (from 240sx but squeezed in)
rally art 4 point harnes (out of 240, lol. i needed a seatbelt cause the stock auto one didn't work)
stock gts lsd
accel coil pack
second rear end
jdm air bubbles in the brake lines
kyb agx all around
2" ebay drop springs
jdm red fender flapping off
2o year old sun roof that still works
dual motorized face cd player with ipod plug
1o" visonik sub box and built in amp
oil leaks there, and there, and there, oh yeah and over there. lol
pealing tint
diconnected power steering
no a/c
neg camber on one side
pos camber on the other
weight reduction stage 1 lol.(removed back seat spare tire and part of the sound deadning)
faded paint
miss match rims (280z turbo on the back, supra celica's on the front)
oh yeah and no power

thats all i can think of for now.

BRING THAT SHIT!!


so yeah... bring it to me and ill fix it up, good as new. With reinforcements.


or goto a pawnshop with 300$ and get a torch, bottles, regulators, and a welder and do it yourself

hvguy wrote:BRING THAT SHIT!!


so yeah... bring it to me and ill fix it up, good as new. With reinforcements.


or goto a pawnshop with 300$ and get a torch, bottles, regulators, and a welder and do it yourself

i already got it taken care of. i got the parts on and stuff. just my tension rod thats still bent and holding on with one bolt. i'm saving up to get the t3 ones though. i'm trying to get some other stuff also but yeah. i work my ass off and don't get paid shit for it. but its a great stress free job.

=P

t3?

when mine broke, it just sheered the bolts off... so I air-hammered the old studs out and fitted it with shitty bolts, so that will happen again....

no need to buy another when you can make "crush points"

hvguy wrote:=P

t3?

when mine broke, it just sheered the bolts off... so I air-hammered the old studs out and fitted it with shitty bolts, so that will happen again....

no need to buy another when you can make "crush points"

i don't have anyone that welds up here and your 4 hours away. besides i need to get some camber plates also to help with alignment and stuff. and to give me that extra angle. besides, i don't plan and understearing anymore(not going to drift in the ran at high speed with cheap ass gripless tires.)

i have shitty tires and don't undasteer when high speed drifting...

you just need mo ebrake yo!

i suck at this ghetto e-typing

CBR_TOY wrote:i have shitty tires and don't undasteer when high speed drifting...

you just need mo ebrake yo!

i suck at this ghetto e-typing

my e-brake doesnt' work. lol. thats why i hit the curb. i started to understeer, going straight at full lock, so i pulled the e-brake and nothing happend. so i turned the wheel so i wouldn't hit the side of it. but the curb was a lot bigger then i thought so i rolled onto it but still messed up the lower control arm and tie rod. the people at the muffler shop were putting my exhaust on and they caught my brake line on fire and then put it out. and ever since then it hasn't worked well at all. suckes. that and i have those jdm air bubbles in the brake lines. lol.