Page 1 of 1
Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Tue May 10, 2011 9:23 pm
by Red Diablo
Hi Guys,
This post is a little long winded so bear with me!
I am rebuilding a 20 spline T50 transmission that I bought standalone so am not sure exactly what model it is out of.
It is being transplanted into a Mk2 Cortina but Sleeve, Transmission Hub No.3 is worn (probably due to jamming into reverse while moving forward) and so far I have been unsuccessful in sourcing a replacement. I have tried Australian toyota dealers, US dealers and Amayama in Japan with no success.
The part is a 33395-14010 which was replaced by 33395-14012.
I recently discovered that in the T50 fitted to the Corolla between August 79 & June 81 another part number (33395-14013) is listed which carried through into the later 22 Spline boxes. Does anyone have any experience rebuilding these boxes and know whether this would be compatible?
I have checked a few web sites and they are listing a 33395-26010 as a replacement for the 33395-14013. Both of these parts are available. from Japan.
Any help would be appreciated.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 11, 2011 7:24 am
by dr.occa
Andrew (aka assassin10000) would be a good person to contact. You can reach him either through here or Club4AG.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 11, 2011 10:20 pm
by Red Diablo
Thanks dr.
I have sent him a PM.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 11, 2011 10:28 pm
by assassin10000
Unfortunately, I don't know this one.
If the gears, shift fork, bearings, etc. are the same part #'s it could work. I haven't looked into this though.
Andrew
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Tue May 24, 2011 7:52 am
by McKenney
Shift forks, bearings, housing(center one the holds main shaft and countershaft) are the same. bell housings and tail housings are different. The main shaft that the shifter pops into is different length due to shifter placement. Gear ratios are close but differ slightly. The third gear synchro I've been told is different but the intermediate shaft still drops into the older trans. I know of a few 3TC guys running 4AG T50's with their bellhousing and tailhousings and the main shifter shaft swapped over. Hope this helps.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 25, 2011 6:09 am
by Red Diablo
Hi Guys,
To provide an update on this thread I ordered the 33395-14013 Sleeve from Amayama in Japan as they indicated that it was in stock. Turns out that the alternative 33395-26010 was the only part available. It was dispatched in Japan on Saturday and arrived in Newcastle yesterday (Tuesday). Very impressed by the delivery time! Whilst the sleeve is different to the original, initial expectations are that it will do the job. It fits the inner gear and the 5th gear side of the sleeve looks the same. The reverse gear side is not machined like the original and looks more robust. Perhaps to make it last longer where subject to abuse. Will try back in the box on the weekend and see how it goes.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 25, 2011 8:47 am
by dr.occa
If you can spare the time, share some polaroids.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 25, 2011 9:00 pm
by 86boy
dr.occa wrote:If you can spare the time, share some polaroids.
Do people still use polaroids?? haha jk jk
some pics would be sweet though!
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 25, 2011 9:03 pm
by Red Diablo
I tried to attach a couple of pics when I first started the thread but it appears that I don't have sufficient permission to post attachments.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Wed May 25, 2011 9:15 pm
by Red Diablo
Before Pics can be seen in a thread at:
http://www.rollaclub.com/board/topic/51 ... nsmission/" onclick="window.open(this.href);return false;
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Thu May 26, 2011 7:25 am
by dr.occa
"fixed"
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Fri May 27, 2011 5:40 am
by Red Diablo
Gearbox is back together and back in the car.
All good.
I didn't get a pic of the replacement ring but the only difference to the original one shown above is that where the one above has a concave machined shoulder (where the red dot is) the new one is not machined so the shoulder is square. The opposite side (5th gear side) is identical to the original.
So in summary the original part was a 33395-14010 that was superseded by 33395-14012 (neither of which are available any longer) there was the potential corolla alternative of 33395-14013 which has been superseded by 33395-26010. This part also suits Hiace's, 4Runners and a couple of other models.
As for buying the parts I now suspect that most of the sites that list the part don't actually carry any stock so in future I'll be going direct to Amayama in Japan.
I also had 7 bearings replaced in the box. Getting those wasn't as easy as I thought it would be either.
Thanks for the comments and posting of the pic.
Re: Part Compatibility between 20 Spline & 22 Spline T50 Box
Posted: Fri May 27, 2011 7:14 am
by dr.occa
Thanks for taking the time to share this information with the 86 community at large Red D.