FS: 16V Parts San Antonio, Tx

Moderators: dr.occa, CBR_TOY

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

All prices are O.B.O. For those not listed, make me an offer. Just get in touch with me.

Image
Image

AE92 Throttle Body $15
It doesn't have the same idle bypass as the AE86, but that can be fixed by drilling a hole I think. In the second picture you can see the bypass hole in the same place as the AE86 RWD throttle body. In the third picture you can see the hole on the right is closed off. This was the 92 bypass hole. The hole on the left is for the 86. Only problem is that the hole is not physically connected to the hole before the butterfly. A small drill bit could probably open in up though. I'll take a look at it and drill the hole if someone is interested.
Image
Image
Image

AE101 GZE Flywheel $30
Image
Image

Stock Cams Sets: $20/ea set
Bigport MR2 Set
Bigport AE86Set
AE101 GZE (wrapped in newspaper).
The set on the lower left is either a smallport set of cams or another bigport 86 set.
Image

Want it? You can have it.
Image

TPS: $15/ea (Check the part numbers in the pick if your interested, just to ensure you can use them...I pulled them from MR2's)
Image
Image
Image

Flywheels (one is definitely a 16v bigport flywheel. the other is either a hi-comp flywheel or a bigport 16v flywheel.) $30 each
Image

Heater Core: $15 Not sure if it can be fixed. It doesn't leak though.
Image

EGR Equipment: $30 for all. I have two charcoal canisters. One has a torn lower vent tube...can be replaced I'm sure.
Image

Bai-ding Plug wires: $25 They were meant for a Camry, but worked find on my 16V. The bulge is supposed to be a capacitor.
Image
Image

FWD Starter Plate: $15
RWD Power steering knuckles: $20
Image

Engine Mount Covers: $10
Pwr Rack Brackets: $10
Image

Water Pump Pullies: $10/ea
Crank Pullies: $15 (only have the AE92 Hi-comp pulley left)
Crank timing Sprocket: $20
Tensioner Pulley: $15
Spark Plug Valley Cover: $15
Image
Image

Oil Pressure Sender: $15
Image

RWD Intake Manifold: $30
FWD/Mid Engine Intake Manifold: $25
GTS Brake Booster: $50
Starter Heat Shield: $15
Passanger-side Engine Bracket: $15
GTS Clutch Master Cylinder: $25
Image
Image

The longer one lines up with my Smallport head, but I'll double check. The other is physically shorter and the ports are closer together. I don't have a bigport head so I can't verify that's what its for.
Smallport rail: Sold Blue-Top/Bigport Rail: $20
Image
Image
Image
Image

Ignitor: $10 (I'll get part number later)
Image

Ueo Replica Fender Braces $100
Image
Image
Image
Image

Coils: $15/ea
Ignitors: All Sold
Image
Image
Image
Image
Image
Image
Image

1-Kouki LSD Axle: $60
1-Kouki Oped Diff Axle: $40
1-Kouki Open Diff Pumpkin/Ring/Pinion: $50
1-Toyota Crush Sleeve: $10
Image
Image
Image
Image
Image
Image
Image
Image


TE manual rack and pinion gears: $40 This is the internals for the rack that contains my QSR. I'm assuming you could put this in any MR2 manual rack case. I don't know if there is a discernible difference between the two gear sets, other than the pinion length

This is the rack housing they came from:
Image

Here are the internals that are for sale:
Image


Kouki USDM Tail lights: $50
Image
Last edited by GTSRolla34 on Fri Apr 02, 2010 2:09 pm, edited 4 times in total.

c4ptiv3
Member
Posts: 601
Joined: Fri Nov 27, 2009 5:10 pm
Location: The Colony
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by c4ptiv3 »

is that 40 for the power steering stuff all shipped? Do you have the lines that come from the pump as well? Also, do you have a cold start injector?
RIP Dustin Fogarty; drift enthusiast, friend
--------------------------
84 GT-S Hatch
14 Fiesta ST

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

I can get you a shipping price. Just give me your zip. I don't have the lines that run from the pump to the rack or the return line. I'll double check just to make sure though. I'll get on that this weekend. I'll also look for a cold start injector. I thought I had one or two laying around somewhere.

c4ptiv3
Member
Posts: 601
Joined: Fri Nov 27, 2009 5:10 pm
Location: The Colony
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by c4ptiv3 »

Zip is 75021 and thanks. Just let me know
RIP Dustin Fogarty; drift enthusiast, friend
--------------------------
84 GT-S Hatch
14 Fiesta ST

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

I'm at work right now, so I don't have access to the parts to get a definite weight or box size, but through UPS shipping looks to be roughly $18. I'm assuming that's mostly due to the weight though. The pump and the bracket aren't the lightest pieces. I'll get a more definite quote either tonight or tomorrow morning.

c4ptiv3
Member
Posts: 601
Joined: Fri Nov 27, 2009 5:10 pm
Location: The Colony
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by c4ptiv3 »

no rush, just let me know.
RIP Dustin Fogarty; drift enthusiast, friend
--------------------------
84 GT-S Hatch
14 Fiesta ST

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

It looks like it would be $58 shipped. Just let me know.

I also put some more parts I have for sale in the first post.

daveskatesallday
VIP Member
Posts: 1760
Joined: Sat Aug 15, 2009 5:04 pm
Location: エビス

Re: FS: 16V Parts San Antonio, Tx

Post by daveskatesallday »

pm sent
"If you love life, don't waste time, for time is what life is made up of."

c4ptiv3
Member
Posts: 601
Joined: Fri Nov 27, 2009 5:10 pm
Location: The Colony
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by c4ptiv3 »

on that rack. Is it the everything I need to put the rack? I would rather have the rack if so. Let me know.
RIP Dustin Fogarty; drift enthusiast, friend
--------------------------
84 GT-S Hatch
14 Fiesta ST

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

There is not housing for the rack. You would need a TE, AE, or MR housing to install these internals. These are just the gears I had left after I installed the QSR.

c4ptiv3
Member
Posts: 601
Joined: Fri Nov 27, 2009 5:10 pm
Location: The Colony
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by c4ptiv3 »

GTSRolla34 wrote:There is not housing for the rack. You would need a TE, AE, or MR housing to install these internals. These are just the gears I had left after I installed the QSR.
ah ok, well give me a paypal email to send the $58 too. Did you find a cold start injector by chance?
RIP Dustin Fogarty; drift enthusiast, friend
--------------------------
84 GT-S Hatch
14 Fiesta ST

Prime123321
Tourist
Posts: 106
Joined: Wed Oct 28, 2009 11:00 am
Location: San Antonio, Texas

Re: FS: 16V Parts San Antonio, Tx

Post by Prime123321 »

I have seen that engine bay before your over off HWY-90 right. I will take those inner tierods off of your hands if you still have them.

Thanks,
David

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

I still have the tie rods. Just let me know for sure.

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

New Parts For Sale: (I'll get pictures as soon as it's possible)

AE86 Front Lower Control Arms (cleaned rust removed and repainted) with Prothane Poly Bushings, Moog Ball Joints (with grease fittings), T3 Steering Knuckles: $150
(if you want the moog inner tie rods also, I'll take $180 for everything)

Again, I'll get pics as soon as I can.

GTSRolla34
Member
Posts: 291
Joined: Fri Jul 17, 2009 11:32 pm
Location: NE San Antonio
Contact:

Re: FS: 16V Parts San Antonio, Tx

Post by GTSRolla34 »

AE86 Front Lower Control Arms (cleaned rust removed and repainted) with New Prothane Poly Bushings (Installed), New Moog Ball Joints (with grease fittings - Installed), T3 Power Steering Knuckles, and Stock Power Steering Knuckles (cleaned of rust and repainted): $150
(if you want the moog inner tie rods also, I'll take $180 for everything)

Post Reply